Acta Mechanica Slovaca 2024, 28(3):36-40 | DOI: 10.21496/ams.2024.028

Specific Aspects of Roughness Measurement

Katarína Paµová, Tatiana Kelemenová1
Technical University of Kosice, Faculty of Mechanical Engineering, Letna 9, 04200 Kosice, Slovakia

The article deals with problems in determining the surface roughness of parts. The arithmetic mean height of the roughness Ra is mainly monitored. This quantity is most often used when defining the required surface quality of components. Assessment of surface roughness is important in the production of parts, their assembly and their use. This article solves some problems in the process of determining this quantity.

Keywords: control system, sensor, traffic light, human machine interface.

Received: October 9, 2024; Revised: October 9, 2024; Accepted: December 12, 2024; Published: September 15, 2024  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Paµová, K., & Kelemenová, T. (2024). Specific Aspects of Roughness Measurement. Acta Mechanica Slovaca, 28(3), 36-40. doi: 10.21496/ams.2024.028
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Whitehouse, D. J.: Surfaces and Their Measurement, 1st ed., Butterworth-Heinemann, 2004. 432 pages. ISBN 9781903996607.
    2. Kumar, S.P.L.: Measurement and uncertainty analysis of surface roughness and material removal rate in micro turning opera-tion and process parameters optimization, Measurement, Vol. 140, 2019; pp. 538-547, ISSN 0263-2241, https://doi.org/10.1016/j.measurement.2019.04.029. Go to original source...
    3. Beňo, J.; Maňková, I.; Vrabel, M.; Kottfer, D.: Roughness measurement methodology for selection of tool inserts, Measurement, Vol. 46, Iss. 1, 2013; pp. 582-592, ISSN 0263-2241, https://doi.org/10.1016/j.measurement.2012.08.017. Go to original source...
    4. Kreith, F.: The Mechanical Engineering Handbook Series. 2nd edition, CRC PRESS. New York, 2005. ISBN 0-8493-0866-6. 2508 pages.
    5. Leach, R.: The Measurement of Surface Texture using Stylus Instruments. NPL National Physical Laboratory. HMSO. United Kingdom. July 2001 ISSN 1368-6550.
    6. Poon, Ch. Y.; Bhushan, B.: Comparison of surface roughness measurements by stylus profiler, AFM and non-contact optical profiler, Wear, Vol. 190, Iss. 1, 1995; pp 76-88, ISSN 0043-1648, https://doi.org/10.1016/0043-1648(95)06697-7. Go to original source...
    7. Jester, W.; Klik, A.: Soil surface roughness measurement-methods, applicability, and surface representation, Catena, Vol. 64, Iss. 2-3, 2005; pp. 174-192, ISSN 0341-8162, https://doi.org/10.1016/j.catena.2005.08.005. Go to original source...
    8. ISO 4287:1997 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters. First edition 1997-04-01. International Organization for Standardization. Geneve. Switzerland.
    9. ISO 4288: 1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture. November 1997. European Committee for Standardization. Brussels. Edition DIN EN ISO 4288 : 1998-04. April 1998.
    10. ISO 3274: 1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Nominal characteristic of contact (stylus) instruments. European Committee for Standardization. Brussels. December 1996.
    11. ISO 5436-1:2000 Geometrical Product Specifications (GPS) - Surface texture: Profile method; Measurement standards - Part 1: Material measures. European Committee for Standardization. Brussels. March 2000.
    12. ISO 21920-1:2021 Geometrical product specifications (GPS) - Surface texture: Profile - Part 1: Indication of surface texture. European Committee for Standardization. Brussels. December 2021.
    13. ISO 21920-2:2021 Geometrical product specifications (GPS) - Surface texture: Profile - Part 2: Terms, definitions and surface texture parameters. European Committee for Standardization. Brussels. December 2021.
    14. ISO 21920-3:2021 Geometrical product specifications (GPS) - Surface texture: Profile - Part 3: Specification operators. European Committee for Standardization. Brussels. December 2021.
    15. ISO 11562:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Metrological characteristics of phase correct filters. European Committee for Standardization. Brussels. December 1996.

    This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content