Acta Mechanica Slovaca 2016, 20(1):22-26 | DOI: 10.21496/ams.2016.004

Influence of Technological Parameters of Production on Properties of Tinplate TH 550, CA

Emil Spišák1,*, Marek Čižmár2, Janka Majerníková1
1 Technical University of Košice, Faculty of Mechanical Engineering, Department of Engineering Technologies and Materials, Košice, Slovakia,
2 US Steel, Ltd. Košice, Slovakia.

The paper was focused on analysis of mechanical properties determined by the uniaxial tensile test and their comparison with production parameters (coiling temperature, finishing temperature, 1st stand reduction and 2nd stand reduction) pertaining to TH 550, CA material. The thicknesses of tinplates were 0.15 - 0.18 mm.

Keywords: tinplate; uniaxial tensile test; finishing temperature; coiling temperature

Published: March 31, 2016  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Spišák, E., Čižmár, M., & Majerníková, J. (2016). Influence of Technological Parameters of Production on Properties of Tinplate TH 550, CA. Acta Mechanica Slovaca, 20(1), 22-26. doi: 10.21496/ams.2016.004
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Pittner, J., Simaan, M.A. (2010). Tandem Cold Metal Rolling Mill Control. Using Practical Advanced Methods. New York, p. 205. Go to original source...
    2. Sharma, R.C. (2003). Principles of Heat Treatment of Steel. New Age International, pp. 87-99.
    3. Banabic, D., Bunge, H.J., Pöhlandt, K., Tekkaya, A. E. (2000). Formability of Metallic Materials. Springer - Verlag Berlin Heidelberg. ISBN: 3-540-67906-5. Go to original source...
    4. Ma, J., Yu, G., Jiang, S., Yang, C. (2012). Research progress on tinplate annealing process. Jinshu Rechuli/Heat Treatment of Metals, Vol. 37 (5), p. 77-80.
    5. Marciniak, Z., Dunca, J.L., Hu, S.J. (2002). Mechanics of Sheet Metal Forming. London. Edward Arnold. p. 231.
    6. Murphy, T.P. (2011). Tin and Tinplate. Uhlig's Corrosion Handbook: Third Edition. p. 853-860. Go to original source...
    7. Wang, X., Zhu, Z., Cai, F., Li, H. (2013). Effects of continuous annealing process on microstructure and properties of electrolytic tinplate. Heat Treatment of Metals. Vol. 38 (6). p. 49-54.
    8. Pittner, J., Simaan, M. A. (2010). Tandem Cold Metal Rolling Mill Control. Using Practical Advanced Methods. New York. p. 205. Go to original source...
    9. Spišák, E., Slota, J., Majerníková, J., Kaščák, Ľ., Malega, P. (2012). Inhomogeneous plastic deformation of tinplates under uniaxial stress state. Chemické listy. Vol. 106, no. Symposia, p. 537-540.
    10. Spišák, E., Slota, J., Majerníková, J. (2010). The evaluation of mechanical properties of tinplates as input parameters for simulation of deep drawing processes. Metalurgija. Vol. 49, no. 2. p. 528-532.
    11. Spišák, E., Majerníková, J. (2013). Analysis of variance of mechanical properties of sheets as the input parameters for simulation ofprocesses. Acta Metallurgica Slovaca. Vol. 18, no. 2-3. p. 109-116.
    12. Spišák, E., Majerníková, J., Spišáková E. (2015). The causes of corrosion formation of packaging sheets after plastic deformation. Materials Science Forum. Vol. 818. p. 121-124. Go to original source...
    13. Spišák, E., Majerníková, J. (2013). Continual annealed single rolled sheets and evaluation of their properties. Journal of manufacturing and industrial engineering. Vol. 12, no. 3-4. p. 30-34. Go to original source...
    14. Zhang, J., Jiang, Y. (2004). A Study of Inhomogeneous Plastic Deformation of 1045 Steel, Journal Engineering Materials Technoly. Vol. 126. p. 164-172. Go to original source...

    This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content