Acta Mechanica Slovaca 2011, 15(1):50-55 | DOI: 10.21496/ams.2011.007

Assessment of Cutting Area Temperature to the Face Milling using Several Cooling Methods

Domnita Florina Fratila

This paper analyzes the temperature variations in the cutting zone under flood cooling (FC), near dry machining (NDM) and dry cutting (DC) conditions. The research compares the dual effects of air-oil mixture in near-dry machining with the cooling effect to dry cutting and flood cooling in terms of the reduction of cutting temperature through the cooling effect, as well as the reduction of heat generation through the lubricating effect to face milling.

Keywords: Cooling Effect, Near Dry Machining, Face Milling, Dry Cutting

Published: March 31, 2011  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Florina Fratila, D. (2011). Assessment of Cutting Area Temperature to the Face Milling using Several Cooling Methods. Acta Mechanica Slovaca, 15(1), 50-55. doi: 10.21496/ams.2011.007
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. Brockhoff T., Walter, A., Fluid minimization in cutting and grinding. Journal of Abrasive Engineering Society, Oct-Nov 1998, Butler, Pa
    2. Dunlap C., Should you Try Dry? Cutting Tool Engineering, vol. 49, no.1, 1997, p. 22-33
    3. Kelly J.F., Cotterell M.G., Minimal lubrication machining of aluminum alloys. Journal of Material Processing Technology, no.12, 2002, Little Island, Cork, Ireland Go to original source...
    4. Machado A.R., Diniz, A.E., Advantages and disadvantages of the use of the cutting fluids. Machining Congress, São Paulo, Brazil, 2000
    5. Marksberry PW, Jawahir IS. A comprehensive tool-wear/tool-life performance model in the evaluation of NDM for sustainable manufacturing. International Journal of Machine Tools and Manufacture, vol. 48, no 7-8, 2008, p. 878-886 Go to original source...
    6. Pusavec F, Krajnik P, and Kopac J. Transition to sustainable production - Part I: application on machinig technologies. Journal of Cleaner Production, vol. 18, no. 2, 2008, p.174-184 Go to original source...
    7. Pusavec F, Kramar D, et al., Transitioning to sustainable production - part II: evaluation of sustainable machining technologies. Journal of Cleaner Production. In Press, DOI:10.1016/j.jclepro.2010.01.015
    8. Rahman M., Kumar A.S., Salam MU, Experimental evaluation on effect of minimal quantity lubricant in milling. International Journal of Machine Tools & Manufacture, no. 42, 2002, p. 539-547 Go to original source...
    9. Weinert K, Inasaki I, et al. Dry machining and minimum quantity lubrication. CIRP Annals-Manufacturing Technology, vol. 53, no. 3, 2004, p. 511-537 Go to original source...
    10. Westkämper E, et al. Life Cycle management and assessment: approaches and visions towards sustainable manufacturing. CIRP Annals - Manufacturing Technology, vol. 49, no. 2, p. 501-502

    This is an open access article distributed under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content